Welded Hydraulic Cylinder Mounting Bracket | Machined Pin Bores

Welded Hydraulic Cylinder Mounting Bracket | Machined Pin Bores

Hydraulic cylinder mounting brackets welded to your drawing: clevis, trunnion and foot mounts with pin bores drilled and reamed after welding in our own shop, chamfers, grease grooves, full penetration welds where specified. 316L or galvanizing on request, ISO 9001:2015.
Send Inquiry
Description
Technical Parameters

Qingdao Tianhua Yihe Foundry Factory is one of the leading manufacturers and suppliers of Welded Hydraulic Cylinder Mounting Bracket | Machined Pin Bores in China. We have world-leading production equipment and strong manufacturing capabilities. Please feel free to buy high quality customized products at competitive price from our factory.

 

A cylinder bracket on a loader arm or a tipping body rarely breaks in the middle of the plate. It tears out at the weld, usually on the return stroke, when the load snatches and the pin bore sees a sudden reversal. That is the failure a hydraulic cylinder mounting bracket has to be built against: enough weld in the right place, fused properly, and a pin bore that stays round.

We weld clevis brackets, trunnion mounts and cylinder anchor plates for makers of mobile hydraulics, farm machinery and industrial equipment. The bracket design and the weld sizes come from your drawing. We bring a DFM check, welding to your callouts, and pin bores machined after welding in our own shop.

Clevis, trunnion or foot mount

Mount Pivots in Strength and limits
Single or double clevis One plane Simple, compact, sensitive to side load
Trunnion One plane, about a central axis Handles side load better, heavier and costlier
Foot or flange mount Fixed, no pivot Rigid, needs accurate alignment with the load

Which one your machine uses is a design decision. What matters to us is that the drawing shows the load direction, so we can see which welds carry the main force.

Pin bores on a hydraulic cylinder mounting bracket

Pin bores are drilled and reamed after welding, never before. Welding heat would pull a pre-machined bore out of line with its partner on the other cheek. Both ends of each bore are chamfered so the pin slides in without picking up. Clevis slot width is cut and ground to the pin size on your drawing. Where the pin runs dry, a grease groove and nipple can be added, and a seat for a thrust washer on brackets that see side load.

Welds on the main load path

On steady-load brackets a correctly sized fillet weld is often enough. On shock-loaded or high-cycle brackets, fillets on the primary path leave an unfused root that is a natural crack starter, and many designers specify full penetration instead. If your drawing shows fillets on a bracket you describe as heavily cycled, we will raise it with you. Thick plate is preheated to the welding procedure, and weld ends are wrapped rather than stopped short.

Finish for the environment

Brackets on agricultural and construction machines are normally painted with the rest of the machine. Marine and outdoor brackets are often 316L stainless or hot-dip galvanized. Painting and galvanizing are carried out by our qualified finishing partners; stainless welding and pickling procedures are adjusted for the material.

Inspection you can expect

Every bracket is checked for pin bore diameter, bore spacing and alignment between cheeks, slot width and weld size. Material certificates come with the shipment. NDT or third-party inspection, SGS for example, can be arranged on request and is quoted separately.

What to send with a bracket enquiry

A complete enquiry for a hydraulic cylinder mounting bracket fits on one page. We need the drawing with weld symbols, the pin diameter and fit, the cylinder model or bore and rod size, the load direction, material and finish, and the quantity, including left and right hand versions if the machine uses mirrored pairs. Mirrored brackets are easy to mix up on the shop floor, so we mark them clearly and pack them separately.

For batch orders, the first bracket from the fixture is measured in full and the report goes to you before the batch runs. Pin bore spacing and alignment are then checked on every part, not on a sample. Because cutting, welding and machining are all done in our own shop, a revision to the bracket between batches is a drawing change, not a supplier negotiation. Prototypes start from a single piece and typically leave the shop within a week of approval.

Cylinder bracket questions

Can you size the bracket from the cylinder model?

We build to your drawing and design loads. If you only have the cylinder model, send it with the load direction and we will tell you what the drawing needs to define.

Can you match an existing bracket?

Yes. Measurements or a sample are enough for us to prepare a drawing for approval.

Do you make brackets in stainless steel?

Yes, 304 or 316L, with a welding procedure suited to stainless.

Send your bracket drawing for a free engineering review and quote. Brackets like these often end up on agricultural machinery frames or welded press frames.

Hot Tags: Welded Hydraulic Cylinder Mounting Bracket | Machined Pin Bores, China Welded Hydraulic Cylinder Mounting Bracket | Machined Pin Bores manufacturers, suppliers, factory

START YOUR OEM PROJECT

Our seasoned technical sales managers are ready to collaborate closely with you. They will take into account your customized requirements, order quantity, and delivery specifics to determine the most suitable quotations tailored to your business. For accurate cost checking, we kindly request that you provide as much detailed information as possible. Rest assured, we will get back to you within 2 hours.

Benefit You Can Get By Partnering With Us

  • Certified Quality
  • ODM Innovation
  • Stable Supply Chain
  • OEM Services
  • Automatic Production Line
  • Multiple Technology Patents
  • Favorable Price
  • Fast Delivery

Send Your Drawings for a Quote