Welded Agricultural Machinery Frame Parts | Batch Production, HDG Optional

Welded Agricultural Machinery Frame Parts | Batch Production, HDG Optional

Welded agricultural machinery frame parts for implement makers: toolbars, tillage frames, hitch brackets, hopper and baler sub-frames. Fixture-based batches after first article approval, vent holes for galvanizing, wear plate on request. In-house cutting, forming and welding, ISO 9001:2015.
Send Inquiry
Description
Technical Parameters

Qingdao Tianhua Yihe Foundry Factory is one of the leading manufacturers and suppliers of Welded Agricultural Machinery Frame Parts | Batch Production, HDG Optional in China. We have world-leading production equipment and strong manufacturing capabilities. Please feel free to buy high quality customized products at competitive price from our factory.

 

Farm machinery is built to be abused. It is dragged through wet clay, bounced across stubble at road speed, parked in a hedge over winter and expected to start work again in spring. The welded frames underneath take all of it. Agricultural machinery frame parts fail in a few familiar places, and most of them can be designed and welded out before the first batch is cut.

We weld frames, toolbars and brackets in repeat batches for implement manufacturers in Europe and North America. Our customers send the drawings. We check them, build a fixture, get a first article approved, and then make the same part every time.

Where agricultural frames usually crack

  • At abrupt changes in section, where a heavy toolbar meets a light bracket with no gusset in between
  • At weld ends stopped in the middle of a member instead of wrapped around
  • Around bolt holes drilled too close to a weld toe
  • At the three-point hitch, which gets used as a jacking point and a tow hook as well as a hitch
  • Inside closed tubes that rust from the inside because water had no way out

Each of these has a simple countermeasure on the drawing: a gusset, a wrapped weld, a moved hole, a thicker plate, a drain hole. When we see one missing we say so in our DFM reply.

Batch production for agricultural machinery frame parts

Implement makers need parts that are interchangeable on their assembly line. Bolt holes have to line up whether the frame came from the first batch or the fifth. That is a fixture job. For each part number we build a welding fixture, or a simpler jig for pilot quantities, then make one first article. It is measured in full and the report goes to you. Only after your sign-off does the batch run, and parts from the batch are checked against that approved first article with go/no-go gauges on the holes that mate with your assembly.

Cutting, forming and welding all happen in our own shop, so a design change between batches does not depend on three subcontractors. Hot-dip galvanizing and painting are done by qualified finishing partners and inspected by us.

Galvanizing details that matter

Most farm equipment ends up hot-dip galvanized, and galvanizing has its own rules. Closed tubes need vent and drain holes, sized and positioned so zinc flows in and out and the part dips safely; we drill them before dipping and can plug them afterwards. Overlapping plates should be seal welded or left with a gap, otherwise acid trapped between them weeps rust later. Threaded holes may need re-tapping after coating. Put the coating standard on the drawing, for example EN ISO 1461, and we pass it to the galvanizer.

Material choices

Q235B, roughly S235, covers most frame members. Hitch brackets, toolbar clamps and highly stressed parts are often Q345B or Q355B. Where soil hits steel, wear plate such as Hardox can be welded on with a suitable procedure, including preheat for thicker grades. We do not make the soil-engaging wear parts themselves, only the frames that carry them.

Working with an implement maker over several seasons

Farm equipment programmes run in seasons. Orders are heavy before spring, a model is updated over the winter, and spare parts are needed for machines that left the factory ten years ago. We plan for that. Fixtures are stored and labelled by part number. Drawings are kept by revision, so a frame for an older model can still be built correctly. When you change a design, we review the revision and tell you which fixtures need modifying and what that costs. Engineers answer emails directly, without a sales layer in between. That continuity, kept up for more than twenty years, is a large part of why implement makers keep their agricultural machinery frame parts with the same supplier.

Agricultural frame FAQs

Can you run a small pilot batch first?

Yes. Pilot runs can use a simple jig to keep tooling cost down before a full fixture is built.

Who does the galvanizing?

A qualified galvanizing partner we have used for years. We drill vent holes before dipping and inspect the parts when they come back.

How quickly can a first article be made?

Usually 5-7 days after drawing approval. Batches follow in 20-30 days.

Can you weld wear plates onto the frame?

Yes, on request. Tell us the grade and thickness.

If you build implements, send us a drawing and annual quantities and an engineer will come back with questions or a price. See also our agricultural machinery welded assemblies and the hydraulic cylinder brackets that often go on the same machines.

Hot Tags: Welded Agricultural Machinery Frame Parts | Batch Production, HDG Optional, China Welded Agricultural Machinery Frame Parts | Batch Production, HDG Optional manufacturers, suppliers, factory

START YOUR OEM PROJECT

Our seasoned technical sales managers are ready to collaborate closely with you. They will take into account your customized requirements, order quantity, and delivery specifics to determine the most suitable quotations tailored to your business. For accurate cost checking, we kindly request that you provide as much detailed information as possible. Rest assured, we will get back to you within 2 hours.

Benefit You Can Get By Partnering With Us

  • Certified Quality
  • ODM Innovation
  • Stable Supply Chain
  • OEM Services
  • Automatic Production Line
  • Multiple Technology Patents
  • Favorable Price
  • Fast Delivery

Send Your Drawings for a Quote