Welded Machine Tool Bed Frame | Ribbed Box Construction, In-House Stress Relief

Welded Machine Tool Bed Frame | Ribbed Box Construction, In-House Stress Relief

Machine tool bed weldments and machine bases in ribbed box construction, welded with a balanced sequence, stress relieved in-house and machined in our own shop to the flatness on your drawing. Or supplied stress relieved and blasted for your own machining. ISO 9001:2015.
Send Inquiry
Description
Technical Parameters

Qingdao Tianhua Yihe Foundry Factory is one of the leading manufacturers and suppliers of Welded Machine Tool Bed Frame | Ribbed Box Construction, In-House Stress Relief in China. We have world-leading production equipment and strong manufacturing capabilities. Please feel free to buy high quality customized products at competitive price from our factory.

 

Weld a three metre bed, measure it on Monday, and it is flat. Leave it in the corner of the shop and measure it again a month later, and it has moved. Residual stress from welding relaxes slowly, and a machine tool bed weldment that was machined before that stress was dealt with will not hold its geometry. Builders of lathes, grinders, gantries and automation machines know this, which is why stress relief and machining sequence are the first things they ask about.

Both happen in our own shop. We weld ribbed box-section beds and bases to customer drawings, stress relieve them in-house, and machine rail seats and mounting faces afterwards. For more than twenty years most of this work has gone to equipment makers in Europe and the US.

Where the residual stress comes from

Every weld bead shrinks as it cools and pulls on the steel around it. In a ribbed bed with dozens of internal welds, those pulls add up to a locked-in stress field. Machining a rail seat removes surface material and upsets the balance, so the bed moves again. Two things reduce the problem: a weld sequence that balances shrinkage left and right, and stress relief before the final machining.

Thermal or vibratory stress relief

  Thermal stress relief Vibratory stress relief
How it works Bed is heated slowly in a furnace, soaked, then cooled under control Exciter is clamped to the bed and run at resonance
Best for Long, heavy, precision beds Shorter or medium beds, faster turnaround
Effect on surface Light scale, removed by blasting No scale
Done by Our own shop Our own shop

Which method suits your bed depends on size, section and the flatness you need. If your drawing specifies one, we follow it; if not, we propose one in our DFM reply.

Machining a machine tool bed weldment after stress relief

After stress relief, rail seats, way surfaces, T-slots and bolt patterns are machined in our own shop to your drawing. On long beds we measure the as-welded shape before machining so enough stock is left where it is needed. Flatness and parallelism are measured and recorded. Machined faces are protected with a rust preventive compatible with way oil, so nothing contaminates the guides during assembly.

Mistakes that make beds expensive

  • Rib spacing so tight the welder cannot reach the seams. The welds then end up undersized or missing.
  • Flatness tolerances applied to every face instead of only the rail seats.
  • No lifting points on a bed weighing several tonnes.
  • Machining allowance left off the drawing, so there is no stock to clean up distortion.

Raw weldments for your own machine shop

Some machine builders prefer to keep finish machining in-house for capacity or confidentiality. We can supply the bed welded, stress relieved and blasted, with the machining stock you specify, ready for your machinist.

How a bed order runs in our shop

After the drawing is approved, plate and sections are cut and the ribs are fitted into the box in a fixture. The welder works from the centre outwards and alternates sides, and long beds may be pre-set with a slight camber so they relax towards flat. The weldment then goes into stress relief, thermal or vibratory, in our own facility. After blasting, the bed is set up on our machine for rail seats and mounting faces, measured, protected and crated. For a machine tool bed weldment this sequence matters more than any single tolerance, because skipping or reordering a step is what causes beds to move in service. Batches of the same bed are built on the same fixture and machined from the same program.

Machine bed FAQs

Do you stress relieve every bed?

We stress relieve in-house whenever the drawing calls for it, and we recommend it for precision beds.

What flatness can you achieve?

Flatness is machined to your drawing. What is practical depends on length and section, and we confirm it during the DFM review.

Can you build a matching column or cross beam?

Yes. Columns, cross beams and bases for the same machine can be built and machined together.

For a quote on a bed or base, send the drawing to our engineering team. Related: welded press frames, robot mounting pedestals and our equipment base and machine frame range.

Hot Tags: Welded Machine Tool Bed Frame | Ribbed Box Construction, In-House Stress Relief, China Welded Machine Tool Bed Frame | Ribbed Box Construction, In-House Stress Relief manufacturers, suppliers, factory

START YOUR OEM PROJECT

Our seasoned technical sales managers are ready to collaborate closely with you. They will take into account your customized requirements, order quantity, and delivery specifics to determine the most suitable quotations tailored to your business. For accurate cost checking, we kindly request that you provide as much detailed information as possible. Rest assured, we will get back to you within 2 hours.

Benefit You Can Get By Partnering With Us

  • Certified Quality
  • ODM Innovation
  • Stable Supply Chain
  • OEM Services
  • Automatic Production Line
  • Multiple Technology Patents
  • Favorable Price
  • Fast Delivery

Send Your Drawings for a Quote